We have found the article on Installing A Bathtub down the page on the internet and concluded it made sense to share it with you here.
Mounting a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging job. If the old tub is easily available, the project can move rapidly; if you have to open up a wall to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as embeded in the new one. Ensure you have qualified on your own for the work and also fit attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will help you mount a new bath tub in your shower room if you have currently gotten a new bathtub as well as do not require to change the plan of your previous water supply pipelines.
Your tools and also material checklist must comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the needed placement. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also check all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet as well as the typical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has actually been made use of at the very least when as this will certainly settle it right into its last position.
Preparing for the Installment
First of all, the supporting structure supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can break rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles utilizing water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog post on How to Install a Bathtub when browsing on the web. Do you know another person who is excited about the subject? Please feel free to share it. Many thanks for your time invested reading it.
Pricing